Fragtfri bestilling over 1.000 kr. Vi fortolder!
HjemBilerElektrobilerElektrobil Touring, Asfalt
Udskriv produktark

CRC MetriCK's Carpet Knife 1/12 Pan Car Kit

Producent Calandra Racing Conceptc Inc.
Tilhører kategori
Elektrobil Touring, Asfalt
kr 4.495,-
Kjøp
Overvåge
+
-
Gem til favoritter
3|4|249
VareID: 65563, Produktnr: 3000
Produktinfo
Anbefalet tilbehør
Dele
Tip din ven
Anmeldelser

Produkt information

1/12 Pan bil
LCG
Konkurrencebil
CRC MetriCKs Road Race 1/12 Pan Car Kit er en 1/12 indendørs bil beregnet til konkurrence. Bilen leveres uden elektronik og karrosseri og dæk der passer til din bane!

Anbefalet tilbehør

PS! Produktteksten er maskineoversat fra norsk.

  • Hurtig og effektiv i sving
  • Lavt tyngdepunkt
  • Enkelt design, let at bruge
  • God holdbarhed
    • Product details in english
    In the front, the MetriCKs features CRCŽs Ultra-tune suspension. Just change the lower C/C plate (caster/camber plate) and your caster and camber are perfectly set. A "4 -1" plate gives you 4 degrees caster and -1 camber. Switch to the 5 -.5 plate and you have 5 caster and negative .5 degrees of camber. Go smash a bunch of barriers, and your caster + camber settings are still the same. We will have a plethora of different combinations available. And this is from Team CRC, so the price for optional C/C plates will be affordable. Throw your expensive setup gauge in the garbage, you wont need it.

    With a simple and quick change of the C/C plate (caster/camber), you can set caster and camber with precision and ease. No setup station, no guessing, no fiddling. Perfect camber and caster is machined into the pieces.

    Speaking of smashing into barriers, a new, flexible 3d printed bumper will help you bounce off the barriers mentioned above. The open design of the bumper increases front downforce.

    We have 6 different front springs available for the car. Ranging from .4mm to .65mm, these springs made with precision from the best material available. The springs will mount over the CRC straight 5mm king pin and should fit other cars as well (A12 and Prodigy).

    The Ultra-tune front end uses the durable 1/8 x 5/16 wheel bearings. These bearings are much stronger than the 3/16 x 5/16 bearing found on many other cars.

    The front mounted side-to-side roll springs separate the roll stiffness from the center/bump stiffness. For those traditionalists that like the side springs in the rear, there is a provision to mount the side roll springs in back. The MetriCKs features an easy to adjust rear center spring for preload, setting battery height and bump stiffness.

    Super easy battery height and droop adjustment. From the top, with a simple hex head, the center preload is adjusted to alter the amount the car "sags in" when race ready. From the bottom of chassis, a simple twist of a wrench on the limit set screw adjusts the "extension" or down travel of the car. Super easy to see and adjust.

    Another goal is low center of gravity. With the MetriCKs, the tungsten weights fit LEVEL with the chassis bottom, not stacked on the chassis or battery plate. We put the ballast at the very lowest position possible. Literally on the same plane as the bottom of the car. Because this car is so lightweight (needing lots of weight) and the ballast is so low, the center of gravity of this car is extremely low. Speaking of tungsten weight, we will have it available, but it is a common tungsten ballast available in many hobby stores, super affordable and easy to get. Keeping with the CRC tradition, high performance at a great price

    Dual linear dampers are super easy to set, change and maintain. The reservoir of damping grease is protected by an easy-to-remove seal from above. Using a line a diff/damper greases (preferred over silicone fluids), the dampers are leak free and easy to maintain and keep consistent.

    The dampers features a large volume reservoir to hold damper grease.
    The car features super strong, precision machined motor plates with a very low center of gravity. Two locking hubs clamp onto a lightweight differential axle which makes is less costly to switch to a differential. Just add a diff hub and bearing to affordably switch to a differential, perfect for the popular GT12R class.

    The new MetriCKs finished 1-2-3-4 at the 2024 Canadian Nationals in 13.5 Super Stock. In the stock class, a solid 1-2 finish matches the same 1-2 finish as the 2024 Snowbird Nationals. The car is already a proven winner!

    Durable, affordable, now with all metric hardware, the new MetriCKs is a proven winner. Pre-order your car today! Shipping before September 1, 2024 (we think it will be even sooner).
    Mere info på engelsk

    Anbefalet tilbehør

    MyLaps RC4 hybridtransponderbil / båd
    3|32|625
    kr 1.795,-
    1s 8000mAh - 55C - Sunpadow Platin Shorty
    3|5|312
    kr 695,-
    1s 8500mAh - 130C - Aerox Hardcase
    3|3|312
    kr 945,-
    1s 7400mAh - 160C - Aerox Hardcase
    3|4|312
    kr 995,-
    Hobbywing XeRun V10 G3 6.5T OnRoad Spec
    3|6|561
    kr 1.149,-
    Sanwa Radio MT-5 m/RX493i 2.4GHz 4ch
    3|6|719
    kr 3.895,-
    Protoform AMR-12 Letvægts 1/12 krop umalet
    3|44|1139
    kr 349,-
    Hobbywing XeRun XR10 Pro HD 120A V4.1 ESC 1s
    3|5|42
    kr 2.395,-

    Produktanmeldelser

    Desværre ingen feedback på dette produkt endnu.

    Giv din feedback
    Produkt
    CRC MetriCK's Carpet Knife 1/12 Pan Car Kit
    Vælg punkter
    Overskrift
    Produkt anmeldelse
    Log ind her
    Retningslinjer
    Produktanmeldelser er beregnet til at dele din oplevelse med andre, der søger kendskab til produktet.
    Irrelevant, forkert eller stødende indhold fjernes.

    Spørgsmål, klager osv.: kontakt os direkte
    Flere så også med



    Størst i Skandinavien
    Om os

    Lynhurtig levering
    Læs mere

    Nem udveksling og retur
    Gå til udveksling og retur
    Prisjakt
    Kundeanmeldelse prisjagt
    Læs vores anmeldelser